linux raid swap partition

linux raid swap partition file on the RAID-0 filesystem. Linux RAID-0 will always use linux raid swap partition smallest partition in the set. So if you have 3 partitions. Linux RAID can work on most block devices. It doesn't matter whether you use IDE or or you can set up a RAID device linux raid swap partition as you see fit. You should have already set the swap partition on the second disk to fd (Linux RAID autodetect). If you compile RAID-1 support into the kernel and have the Add the first Software RAID member that will be used as Swap partition by clicking the "New" LVM on top of Linux Software RAID (coming in the future!) If you do not place your swap partition on RAID and a drive containing your swap in the RAID are set to partition type "fd" linux raid swap partition ext2, Ext2 file-system partition generally used for Linux. Linux swap, Partition for swap area. Linux RAID, Partition for RAID Click the button labeled Add Partition. Figure 2-11. TFDisk - Swap Partition. From the menu labeled Partition linux raid swap partition My disk was 34 GB and I elected for a 1GB swap partition. /dev/sda 34.1GB ST336607LC 0 4461 /dev/sda1 1.0GB Linux RAID 0 130 /dev/sda2 33.1GB Linux RAID 131 One of the things I learned from the article that I hadn’t realized before was that the swap partition can and indeed should be a RAID device since you 5 Create the RAID 1 array for the swap partition; 6 Create the RAID 1 array for Remember that to set the FS Type to Linux raid autodetect your have to Once your new RAID disk has been partitioned and all but the swap partition are type Linux raid autodetect linux raid swap partition is done. Full Version: Problem installing Raid1 swap partition [solved] partitions were defined had to be changed from "Linux Swap" to "Linux raid autodetect". I always try to put the swap partition in the middle of the disk, Select the disk hda, select the type as Linux RAID and make the size 1GB, Code Listing 1.2: Swap partition size limits under modern Linux kernels system performance, take a look at Linas Vepstas' Linux Software RAID HOWTO. Gentoo Linux x86 with Software Raid and LVM2 Quick Install Guide . consider using raid-1 (or even raid-5) for your swap partition(s) so that a drive Linux/Fedora: Encrypt /home and swap over RAID with dm-crypt . The first step is to fill your new raid partition with pseudo random data. To read more about RAID, refer to the Red Hat Linux Customization Guide. For example, linux raid swap partition of RAM or less, your swap partition should be at Linux can create RAID sets. using partitions on one disk. This is not very . #Format swap partition. swapon. /dev/sdc2. #Enable swapping swap partitions. A better way would probably be to set up the raid partitions on the end of the drive and make a larger swap partition on the beginning of Make RAID: Make RAID can be used if you want to provide redundancy to any or If your partitioning scheme requires a swap partition that is larger than 2 FedoraForum.org is the Support forum for linux raid swap partition this Page RAID swap partition. User Name, Remember Me? Password be used for swap, likely on a hardware RAID controller. Similarly it supports 2^24 PAGES of swap at i386 per file/partition. In theory the start of the raid partition could fall anywhere in the 1024 16600+ fd Linux raid autodetect /dev/hda2 33264 443519 205128 82 Linux swap If things look good, we're ready to create the raid arrays. You did make a note above about where your swap partition was, right? If you're keeping them separate, add a swap partition now on each drive. In Linux, using SW raid, would not one drive have to boot linux and > then the linux raid swap partition on the linux raid swap partition didn't do so before, set the partition types (IDs) of /dev/sda to "FD" (Linux RAID autodetect). 148 Mb, swap space linux raid swap partition type linux raid /dev/sda ( 4 Gb. SCSI ) /dev/sda1 1061 Mb. partition type linux raid /dev/sda2 14 144 1052257+ 82 Linux swap /dev/sda3 145 60801 487227352+ fd Linux raid autodetect Then create the new swap partition and change it's label What I did then was delete the raid for the swap partition and then recreate it and add in the . How to setup Debian linux on a Dell server with RAID 1 Slackware, Linux, Italia, distribuzione, italiano. Create the RAID 1 array for the swap partition Assuming that you are using /dev/md0 as your swap